download
REMOVAL All Models 1. If equipped with saddlebags, removal may ease installation. Follow the instructions in the appropriate Service Manual or Instruction Sheet. 2. See Figure 1. Remove and discard the forwardmost fender support bolt (1). Repeat for the other side. 3. See Figure 2. On the left side, remove the footrest support mounting bolt (1) and footrest support bracket assembly (2). Discard the mounting bolt. 2005 – 2006 Models 1. Loosen the exhaust shields as necessary following the instructions in the appropriate Service Manual. Move as necessary for access. 2. Loosen the exhaust header nuts following the instructions in the appropriate Service Manual. 3. See Figure 3. Remove bolt (1) connecting the exhaust system (2) to the support bracket (3). 4. See Figure 4. Remove the two rear muffler bracket bolts (1). 5. See Figure 5. Move mufflers enough to access the rear bolt attaching the exhaust mounting bracket to the frame. Remove bolt (1) and discard. 2007 – Later Models NOTE On 2007 – later models, the frame tab (4) has a plug instead of a bolt (see Figure 6, item 1). 1. Remove plug and discard. 1 is05313 1. Fender support bolt (discard) Figure 1. Remove Docking Hardware 1 2 is05320 1. Footrest support mounting bolt 2. Footrest support bracket assembly Figure 2. Footrest Support Bracket Assembl NSTALLATION Right Side See Figure 5 or Figure 6. 1. See Figure 7. Install upper screw (7) in the fender support. Tighten screw finger-tight. 2. Install the lower screw (4 or 5) with the saddlebag guard, washer (9) and locknut (6) inside the frame. Tighten screw finger-tight. 3. Tighten the upper screw to 30 ft-lbs (41 Nm) . 4. Tighten the lower screw to 40 ft-lbs (54 Nm) . Tighten nut to 30 ft-lbs (41 Nm) . 5. 2005 – 2006 Models: a. Loosely install the exhaust header bolts. b. See Figure 4. Loosely install two rear muffler bracket bolts (1). c. See Figure 3. Loosely install bolt securing exhaust system (2) to support bracket (3). d. Tighten exhaust header bolts following the instructions in the appropriate Service Manual. e. Tighten support bracket bolt and rear muffler bracket bolts following the instructions in the appropriate Service Manual. f. Tighten exhaust shields following the instructions in the appropriate Service Manual. 6. Install saddlebag (if removed) following the instructions in the appropriate Service Manual or Instruction Sheet. 1 2 3 4 is05333 1. Lower saddlebag guard screw 2. Upper saddlebag guard screw 3. Saddlebag guard 4. Exhaust support bracket Figure 5. Install Saddlebag Guard – Right Side Shown (2005 Models) -J04645 2 of 4
2 1 3 4 is05332 1. Lower saddlebag guard screw 2. Upper saddlebag guard screw 3. Saddlebag guard 4. Frame tab Figure 6. Install Saddlebag Guard – Right Side Shown (2007-Later Models) Left Side 1. Loosely install upper screw (7) through the saddlebag guard and the fender support. NOTE Spacer (8) must be installed with the chamfer facing out. 2. See Figure 7. For 2005-2006 Models: Install lower screw (3) through the saddlebag guard, saddlebag guard spacer (8), footpeg support and the frame. Tighten to 30 ft-lbs (41 Nm) . For 2007 and later Models: Install lower screw (10) through the saddlebag guard, footpeg support and the frame. Tighten to 30 ft-lbs (41 Nm) . 3. Tighten upper screw to 30 ft-lbs (41 Nm)
Incoming search terms:
- how to install saddle bag latch kit on harley davidson
- saddlebag bushing lower support - Bing
- 05 vento v thunder parts manuel
- removing road king bag rails videos
- removing saddlebags from goldwing 1800
- repair plastic back heritage softail saddlebag
- saddlebag support brackets for triumph bonneville
- service manual for a 2006 victory jackpot
- tighten sunshade highlander
- klr650 saddle bag mounting brackets
